解決方案：

Solutions：

1. 關閉電源及水源，確保維修安全
2. 徹底清潔滲水區域，去除老舊密封膠
3. 檢查管道接縫是否有裂縫或變形
4. 使用高溫耐腐蝕密封材料進行密封
5. 安裝加固配件，防止再次變形
6. 測試防水效果，確保無滲漏後完成維修

1. Turn off power and water supply to ensure repair safety
2. Thoroughly clean the leaking area and remove old sealant
3. Check if there are cracks or deformation in the pipe joints
4. Use high-temperature and corrosion-resistant sealing materials for sealing
5. Install reinforcement accessories to prevent re-deformation
6. Test the waterproof effect and complete the repair after confirming no leakage

專業工具：高壓清洗機、密封槍、測漏儀等

Professional tools: High-pressure cleaner, sealing gun, leak detector, etc.

解決方案：

Solutions：

1. 立即切斷電源，禁止繼續使用
2. 使用漏電檢測儀定位漏電點
3. 檢查電線絕緣層是否破損、老化
4. 更換破損電線及配件，重新佈線
5. 安裝漏電保護裝置，加強安全防護
6. 全面檢測絕緣性能，確保無漏電後通電測試

1. Immediately cut off the power supply and prohibit continued use
2. Use an electric leakage detector to locate the leakage point
3. Check if the wire insulation layer is damaged or aging
4. Replace damaged wires and accessories and rewire
5. Install leakage protection devices to enhance safety protection
6. Comprehensively test the insulation performance and conduct power-on test after confirming no leakage

安全提示：漏電可能導致觸電危險，切勿自行拆解

Safety reminder: Electric leakage may cause electric shock hazard, do not disassemble by yourself

解決方案：

Solutions：

1. 關閉電源，等待一段時間後嘗試重啟
2. 檢查電源線是否有磨損、短路情況
3. 檢測電機運行電流，判斷是否超負載
4. 檢查保護開關是否正常工作，必要時更換
5. 清理電機及風輪灰塵，減少運行負載
6. 全面檢查電路系統，排除短路隱患

1. Turn off the power and wait for a period of time before trying to restart
2. Check if the power cord is worn or short-circuited
3. Detect the motor operating current to determine if it is overloaded
4. Check if the protection switch is working normally and replace if necessary
5. Clean the motor and wind wheel dust to reduce operating load
6. Comprehensively check the circuit system to eliminate short-circuit hazards

注意事項：多次跳制可能是嚴重故障信號，需及時維修

Note: Multiple tripping may be a signal of serious failure and needs timely repair

解決方案：

Solutions：

1. 切斷電源和水源，排空設備內殘餘水分
2. 拆卸舊水泵，檢查安裝位置是否有損壞
3. 清潔水泵安裝區域，去除雜質和水垢
4. 安裝匹配型號的新水泵，確保接線正確
5. 連接水管，確保密封良好，無漏水
6. 通電測試水泵運行狀態，調試水流壓力